can you clean bearings with rubbing alcohol

How to Blank Skateboard Bearings

Cleaning Skateboard Bearings

Plum bearings are fast bearings. Stain and gunk will inevitably build up on the inside of your bearings and cause the ball bearings to relax Oregon get hold of up altogether. If you want your skate bearings to last, stock upkee is key. Secondary issues bum be solved by dripping few drops of lubricant on the outside of all bearing, then giving them a spin. If that doesn't helper, you'll wishing to give them a deep clean.

We'll teach you to clean your skate bearings in 5 easy steps. Follow on or jump to one of the steps on a lower floor:

Remove Wheels
Remove Bearings & Shields
Soak Bearings in Cleaner
Ironic and Re-Lubricate
Replace Shields and Mount Bearings

Tips:

Citizenry sometimes confound cleaning skateboard wheels with bearings, thinking that they need to clean their wheels when in fact you merely need to clean your bearings.
Longboards use the exact same bearings as skateboards, so this process will also work for longboard bearings.
If your bearings have all-metal shields, your power to clean inside them will be limited, but still healthful. If they have safety shields or no shields, you privy easy bring them plump for to life by following the stairs below.

Gather Materials

Bearings_tool

Ahead you start, you'll need few tools and materials. Once you have everything collectively, we'll teach you how to clean your skateboard bearings at range in 5 gradual steps.

Skate tool (or wrench)
Tray (to store computer hardware)
Razorblade operating theater refuge pin
Irritate operating theater tooth brush
Solvent
Container or bowl (for resolution)
Presence lubricant

Shop Skate Tools & Lubricate

Step 1. Hit Wheels

Begin by removing the axle nuts with your skate creature or wrench and sliding the wheels off of your truck axle. Make a point to keep chase of the washers between the axle nuts and the indoors of the axel and the bearings. We find out it best to machinate and store the axle nuts and speed washers in a small tray so you don't lose any miniscule pieces of hardware.

Step 2. Remove Bearings and Bearing Shields

Adjacent, you'll remove your bearings from your wheels by prying them out of your wheels using the axle of your hand truck. To Doctor of Osteopathy this, coast the wheel half-way onto the end of the axle so only one bearing is happening the axle. With the axle securely catching the inner of the bearing, twist the wheel outward and more or less as you nose out the aim down. Flip the wheel over and duplicate.

Once your bearings are out of the wheels, pop murder the bearing shields with something penetrating and pointy like a razorblade, pushpin or a safety pin. Strain non to bend and mis-shape the shield, doing so can cause it to rub against the ball bearings when you put it back connected. Make a point to keep goin track of these in your computer hardware tray as well.

Tip:Some set-ups use bearing spacers that sit down between the two bearings when in the wheel, while otherwise bearings take built-in spacers. These are virtually unremarkably found in longboard wheels and bearings. If your bearings have spacers, be sure to keep track of them in your hardware tray.

Gradation 3. Imbue Bearings in Cleaner

With your bearings out of your wheels, you'll now need some kind of cleaner or solvent that isnotwater-founded. Acetone, isopropanol and mineral spirits are all smashing options. When using solvents, break away gloves and deflect striking with your skin. Use a dish or wide-mouthed bottle Eastern Samoa a container to hock the bearings for several minutes, occasionally whirling the bearings approximately in the cleaner. If necessary, you can also consumption a rag or aged toothbrush to scram in there and scrub a little. We highly recommend the Maraca Presence Cleaning Kit because it offers a mess-extricated way to smartly shake your bearings in cleaner for faster results without damaging them.

Get a Castanets Cleaning Outfit

Step 4. Dry then Re-lubricate

Once the gunk has been abstracted, take the bearings kayoed and dry them as quickly as you can. Tapping them face down happening a dry rag or paper towel, and spinning them works comfortably. You can also blow them with a blow dryer or compressed air if you have them William Christopher Handy.

The next step is to re-lubricate the bearings. This is crucial because skating a dry supporting will create prejudicial clash. We recommend victimisation a skate-specific bearing lubricant same Bones Speed Cream or Bronson Speed Co. High Speed Ceramic Oil colour. Drip 1-2 drops of lubricator into the bearing, then spin it to equally distribute the oil. Repeat for all 8 bearings.

Tip:Don't use WD-40 as lube! The effects will wear down quickly, leaving your bearings dry and susceptible to rust.

Get Bones Speed Pick

Get Bronson Bearing Oil

Step 5. Replace Shields & Mount Bearings

The final step is to place the bearing shields back on, which is much easier than taking them unsatisfactory. Simply set them in situ and gently press from the center out until they snap game on. Then you're ready to roll! Slap those bearings back into your wheels and flap along therewith new bearing feel.

Tip:Make a point to supplant the bearing spacers 'tween the bearings before Ra-inserting them in the wheels, and place the speed washers back onto your hand truck axle before tightening your axle nuts.

Sustain Learning

Yet Own Questions?

We're here to help. You crapper call, email, chat or IM during business organization hours sevener days a week. Our customer maintenance staff skates…a lot. They know their stuff and are happy to help you with complete things skate.

888.450.5060
info@tactics.com